VT
ph: 802-793-7023
Removed from a 230C Deere - they are 15-20k new. Asking 6k, make an offer!!!
Just in - 24" Cat branded bucket- for Cat 315 and 316 linkage- fits most series but tagged for c/d./e series machines Part number 353-1585- setup with dead pins for grabber. Bucket looks very nice, doesn't show much wear. .46 yard capacity. Good teeth and side cutters. First $3,000
Also just in- Bucket for 325 cat- Tagged as C series but believe it fits most- part number 134-1890 - 42", 1.5 yard capacity. Was used on a coupler, still has dead pins. Little scalloping between teeth but not bad. Bottom and back look good, still wear bars there. Look's like one ear was welded at one point. These are huge money new as you know. Good option for an older rig. First $3500.
Also have a really nice heavy duty frost tooth, ripper for cat 305, 305.5, yanmar 45/50, etc. 45mm pin sizing.
Just in - 5 more 60" clean up - fitment as follows
(2) Deere wedge coupler 50/60 size machine
KX057
Hyunda 55-60, Case or New Holland 57 or 60
Cat 305/306- Yanmar 45/50
The above all look like the picture below-
18" trenching bucket for Cat 307- set up for pin grabber- comes with dead pins. First $1250
Just in- 30" Cat dig bucket- New unused bucket! 40mm pins. 6" stick clearence (width between ears) 10" center to center front to rear pin. New leftover bucket. Was told it would fit a 304 (d,e, e2 series, not the older series) but can tell you for fact it won't go on with a factory quick coupler, spread is too far. Should go on a pin on unit with no coupler - may also fit the older 304.5's- Should fit some other makes in same size category- just check your dimensions.
(5) more new cleanup buckets just in- aftermarket- All 60" (5') - see list below
Wainroy/tag style with 1.25" keeper pin
Kubota (with factory style coupler) KX057-4
(2) Kubota KX080 with factory style coupler
Cat 307/308, to fit factory pin grabber style coupler. $1700 each. These are closeout on this brand, I have 5 more coming at some point, then they are gone!!! Well built buckets. They have just chose to focus on only building tilt style buckets.
48" clean up /dredging bucket for Cat 311 /312 linkage- 65mm pin size- Cat brand bucket- Pretty good shape, some minor floor denting, solid though and a good straight bolt on edge- $2,000
28" smooth edge dig bucket. Very good shape, looks like minimal use- welded on it says 312, (311 linkage same- as well as older cat e110 and e120) 65mm pin size-- Would also make a good bucket to add adapters and teeth to and have a real nice dig bucket for a fraction of the cost of new. First $1500 steals it!!
Teran 42" dig bucket with teeth for Cat 307 linkage. These are a pretty decent bucket, and well priced at $1800.
(5) 48" clean up buckets- aftermarket-applications below-
Cat 307/308 factory pin spec or grabber
bobcat exchange style coupler
Kubota KX040 factory style quick coupler with pin through the rear and ears on the front
Cat 303-and d-series or newer 304- factory pin spec or grabber style coupler
Cat 305, 305.5, and 304c series or older factory pin setup or should fit grabber as well- This will also fit Yanmar or Gehl 45-50 size with hyd coupler
47" Cat brand clean up, with pins and bolt on edge, new- fits 304c model and older, all 305 and 305.5. Priced at $1800.
Kubota OEM 30" digging bucket for Kubota KX080-3 excavator - 30" with teeth. Pin on style, not for the quick coupler. New, yard weathered, sells for about $1800. First $1000 buys it.
Used 30" CF pin on bucket. Came off a Kobelco SK60- 30", 50mm pins i believe. Shaped like a dig bucket but its a smooth lip clean up style. Good shape. Can get more measurements if you like or come take a look. If you have a similar size machine I can measure or come take a look. $600
NEW-aftermarket 24" for Cat 416, 426 etc, with teeth, $1400
Cat Used bucket for cat 446 backhoe, ok shape, $600.
Also have a used Concrete cruncher that came off of a 230C Deere- Call with your application and I'll see if I can sort it out. Asking 6k- Probably needs pins- about a third the price of new!
Below are some units I have pictures of/ all below units are in list above.
Buckets-
Cat 48" dredging style with weep holes- for 311/312 linkage. 64mm pin size, about 9" stick spacing- Pretty good shape, minor dent in floor, good edge. $2,000
28" smooth edge bucket- welded on it is 312- however, by measurement looks more like 65mm pin to me and wider spacing for stick- approx 10.5"- common 120-130 sizing- deere, hitachi, case, etc. bring your measurements and compare! In really good shape. Wood be good pipe backfill bucket-- or add a new base edge/shank kit and have a cheap digging bucket. First $1500.
30" CF bucket- shaped like a dig bucket but its a smooth lipped clean up bucket- was on a Kobelco sk60 50mm pins I beleive. $500
New Kubota (oem) 30" digging bucket- pin on style, kubota number k7413 - fits Kubota KX080-3 Does not fit kubota coupler, this is a direct pin on. New Price $1700. Just a little yard weathered but new. My price $1,000.
New aftermarket- for Cat 416, 416B 416C, 420, and I bleieve 430 as well. 24" with teeth $1400
Used, for cat 446 backhoe- Cat brand- $600
Thumbs-
machine fit is approx, will need measurements from your application.Thumbs below are in stock, no waiting!
Gentec thunbs-
Manual 8" wide by 30" long, 6-10k lb machines- $795
Manual 18" wide by 50" long- 24-39k lb machines- $2250
(2) hydraulic 8" wide by 30" long- 6-10k lb machines- $1250 each
Tomahawk thumbs-Only available for in one size-
Manual 36" 12-17k lb machine- please note, these are not quite as rugged as the above Gentecs- in my opinion- but have sold many and they are adequate if not in extra heavy duty use.
$650 each- two available.
Copyright 2013 Dion Equipment Sales Inc. All rights reserved.
VT
ph: 802-793-7023